10/29/2020 Hunter Pcz 10140 Product Manual Download
www.HunterFan.com
Advertising
Hunter Pcz 101 40 Product Manual Download Pdf
1.1 About This Manual This manual contains important operation, maintenance, and safety information for the DSP700T Series Sensors. It is supplemented by the alignment system console operation manual. Read and become familiar with the contents of these publications.
1.888.830.1326
Pro-c. Read online or download PDF. Hunter PRO-C (PCC) User Manual. Manuals Directory ManualsDir.com - online owner manuals library. Hunter manuals. Control panel. PRO-C (PCC) Manual Hunter PRO-C (PCC) User Manual Pro-c. Complain Advertising. This manual is related to the following products. Manual Operation The PCZ-100 and the ICZ-101 utilize two manual operation methods—an internal manual bleed and an external manual bleed. To operate the valve manually, choose from either of the following procedures. Turn the solenoid or the bleed screw 1⁄2 turn. To stop manual operation simply tighten either the solenoid or the.
Model #99120
Universal Wall
Mount Control
Getting Started
Wiring the Receiver
Wiring the Wall Control
OR
OR
OR
Remove the canopy. If uncertain how
to remove it, reference the fan’s owner’s
manual. With wiring exposed, it may be
helpful to note existing wire connections
or take a digital photo for reference.
Remove the wire connectors that connect
the wires from the outlet box to the fan,
leaving the grounding wires connected.
CONNECT WIRES FROM
RECEIVER TO FAN - Using the blue wire connectors, connect the white wire from the receiver (marked “common out”) to the white wire from fan. Connect the black wire from the receiver (marked “fan out”) to the black wire from the fan. Connect the blue wire from the receiver (marked ”light out”) to the blue wire (or possibly black with white stripe) from the fan.
If you are uncertain about
wire colors or connections, please contact a qualified electrician.
CONNECT WIRES FROM
RECEIVER TO WIRES FROM OUTLET BOX - Using an orange wire connector, connect the black wire (ungrounded) from the ceiling to the black wire from the receiver (marked “live in”). Connect the white wire (grounded) from the ceiling to the white wire from the receiver (marked “neutral in”).
AFTER ALL WIRES ARE
CONNECTED and secured with wire connectors, re-install the canopy.
Before installing the Universal
Remote Control Receiver,
use the pull chains to set the
fan speed to HIGH and the
light to ON. Be sure power is
OFF before proceeding with
installation.
Choose the hanging system that most closely resembles the one used by your fan and install the receiver as shown and wire as directed.
Note: Some fans may have considerable excess lead wire. For easier canopy installation, cut the excess wire, leaving a minimum of 8” remaining. Re-strip the fan lead wires 1/2”. Place remaining excess wire into
the ceiling electrical box. The bracket and fan must remain properly grounded.
You may have installation issues if the fan is installed on an angled ceiling. For assistance, call 1-888-830-1326.
Ceiling
Plate
Receiver
Canopy
Receiver
Canopy
Ceiling
Bracket
Receiver
Fan Body
Cable Tie
For low profile fans, the receiver should
be secured to the ceiling bracket with a
cable tie.
![]()
Receiver
Canopy
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off
the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers
in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
M0061-01 • 07/26/13 • © Hunter Fan Company
FR
OM
RECEIVER
whit
e
black
blue
whit
e (c
ommon out)
black (fan out)
blue (ligh
t out)
FROM FAN
FRO
Hunter Pcz 101
M RECEIVE
R
FR
OM CEILING
black (ung
rounded)
whit
e (g
rounded)
whit
Hunter Pcz 101 40 Product Manual Download 2017
e (neutr
al in)
black (liv
e in)
Turn
Pow
er
OFF
After removing the switch plate
cover, remove all wiring from
the switch.
Using orange wire connectors,
connect the two black wires
(ungrounded) from the outlet
box. Also connect the two green
or bare wires (grounding) from
the outlet box with the grounding
wire from the wall control.
Insert the wall control into
the outlet box and secure the
two screws using a Phillips
head screwdriver.
Install the cover plate using a
Phillips Head screwdriver to
secure the two cover plate screws.
Advertising
Hunter Pcz 101 25
Popular Brands
Hunter Pcz 101 40 Product Manual Download Free
Popular manuals
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |